RF's Synth Module by Module

June 2008.

Cab 1

Cab 2

Cab 3

Cab 4

Cab 5

Cab 6

2 VC LFO ( MFOS /Ray Wilson PCB)

Simultaneous Sine, Triangle, Saw, Ramp, and Variable Pulse Width Rectangle Outputs.

Voltage Control of Frequency (approximate log response, NOT 1V/Octave)

Voltage Control of Rectangle Pulse Width

Fine and Coarse Frequency Control

Very Low Frequency (1 Cycle per several minutes)

6 VCO ( MFOS /Ray Wilson PCB)

Simultaneous Rectangle, Sawtooth, Triangle and Sine Outputs (Saw core design)

Designed for 1V/Octave control voltage

3 1V/Octave control voltage inputs.

1 Linear control voltage input.

Hard sync input.

Rectangle wave duty cycle adjustable between 10% and 90%

Rectangle wave duty cycle voltage controllable

1 16 Step Sequencer ( MFOS /Ray Wilson PCB)

Produces sequences of 4 to 16 steps in length

Modes include stop at count, reverse at count, reset at count and random 16 mode

Each step has coarse tune, fine tune, and switchable gate

Accepts external clock and external start pulse.

Simultaneous outputs with and without portamento.

Forward, Back, and Reset controls.

3 24 DB VCF ( MFOS /Ray Wilson PCB)

Four Pole 24dB Per Octave Low Pass Filter

Log Response to Control Voltage (1V/Oct Tunable)

Makes A Nice Sine Wave Oscillator

Voltage Controlled Cut-Off Frequency

Voltage Controlled Resonance

1 12 DB State Variable VC Filter ( MFOS /Ray Wilson PCB)

State Variable VCF 12dB/Octave With VC Resonance

Simultaneous High-Pass, Low-Pass and Band Pass Filter outputs.

Log Response to Control Voltage (1V/Oct Tunable)

Sine Wave Oscillator at full resonance

Voltage Controlled Resonance (Linear control)

5 Dual VCA ( MFOS /Ray Wilson PCB)

Log and Linear Response to Control Voltage

DC Coupling Throughout

1 Autopan ( MFOS /Ray Wilson PCB)

Leslie Spin-up/Spin-down Simulator

Mimics the Rhodes Stage Piano stereo tremolo

CV Control of Panning Rate.

(On same panel is the QFG)

1 Thomas Henry QFG (Perfboard)

The Quadrature Function Generator produces 4 simultanious sine wave voltage outputs 90 degrees out of phase.

1 VC Phaser ( MFOS /Ray Wilson PCB)

Switchable 4 or 8 stage phase shifter.

Variable feedback ranges from mild swooshing to raucous mind bending.

Two external control voltage inputs.

Pseudo stereo output when 4 stage and 8 stage outputs are used.

On-Board LFO produces Triangle and Ramp waves.

Phase angle is modulated in a logarithmic fashion.

8 Stages of phase shift result in a barber pole effect.

1 Sample and Hold ( MFOS /Ray Wilson PCB)

Sample Rates from .05HZ to 1KHZ.

Voltage Controlled Sample Clock

Clock Sync-In Can Double As External Clock In

Glide Control To Slew Between Samples.

4 Envelope Generator ( MFOS /Ray Wilson PCB)

1 mS to 20 second Attack, Decay, and Release times.

Classic ADSR envelope shape and functionality.

Gate and trigger inputs permit retrigger after Attack complete.

Comparators on gate and trigger inputs.

2 Noise Cornucopia ( MFOS /Ray Wilson PCB)

White Noise.

Pink-ish Noise

High Pass Noise

Adjustable Grainy Noise.

Adjustable Random Gates.

1 Foniktron SSM2044 VCF PCB

A Voltage Controlled Low Pass Filter Based on the SSM2044 Chip.

1 4 Step Analog Sequencer (Perfboard)

Simple 4 step sequencer based on the CD4017 decade counter chip. It uses a 555 based Clock and CGS Trigger to Gate converter.

1 Aaron CRAM Portamento / RingMod (Perfboard)

Portamento is the 'glide' from one note to another.

This module can be used as an LFO with the toggle switch in that position

The Ring Modulator takes two signal inputs and outputs a sum and difference of them. Often used to provide 'clangorous' sounds such as bells.

1 CGS Slope Detector / Dave Magnuson NOR Logic Gates (Perfboard)

The slope detector is an event-driven gate/trigger generating device. It monitors a control voltage, and responds according to what that voltage is doing. If the voltage is rising, the slope detector gives a "gate" output (approx. 5V) on its "rising" output. Likewise, if the voltage is falling, the slope detector gives an output on its "falling" output. The duration of this gate signal depends on the incoming CV and the setting of the sensitivity pot. When the CV is remaining constant, the "steady" output activates.

These gate signals can be used to fire envelope generators dependent on the action of the CV, for example opening a filter when a melody is rising in pitch, and closing it when the melody is falling in pitch. It can also be used to generate gate signals from LFOs, envelope generators, to advance sequencers etc.

The sensitivity pot allows the slope detector to work with either relatively fast events, like the edges of a square wave pulse train, or very slow events, such as the sine output of an LFO being used to drive filter/phaser sweeps.

3 4 Input Mono Mixer (Perfboard)

Basic 4 input mono mixer based on a TL084 Op Amp. 4 Summed outputs.

1 4 Input Dual Mono Mixer with VU Meters (Perfboard)

4 input Dual mono mixer with 2 outputs per channel, plus Stereo Headphone jack.

3 4*4 Mults

Four sets of Four 1/4 inch Jacks summed together for splitting control votages or audio signals to different locations

1 S to V trig Converter / Mults

Converts Moog "S" trigger to "V" trigger for triggering events from the Micromoog. Mults split CV from Moog to VCO's

1 Serge Peak/Trough (Perfboard)

This has two sections, each with four inputs and one output. The peak section would output the highest of the four inputs, while the trough section would output the lowest of the four inputs. The peak section was often used for combining gates from a sequencer, but either section could used to combine waveforms, CVs or envelopes in unexpected ways.

1 Wogglebug #3 PCB

The "WoggleBug" is a random voltage generator. It is a continuation of "smooth" and "stepped" fluctuating random voltage sources pioneered by Don Buchla. The core of the circuit is based on the Buchla Model 265 "Source of Uncertainty" module.

1 CGS BPF (Dual) (Perfboard)

A utility bandpass filter for creating artifical instrument resonant cavities etc.

1 Harry Bissell Morphlag (Perfboard)

A Lag circuit with independent ATTACK and DECAY controls and a SHAPE control to

vary the response from linear to log.

1 CGS Wavefiolder / CV Mixer (Perfboard)

The Simple Wave Folder - The effect it produces is not like unlike that of the Serge middle wave multiplier - harmonically rich waveforms that can be swept for filter-like effects. It MUST be fed a triangle or sine wave to function properly.

1 CGS Psycho LFO / Magnus Danielson Sawtooth Doubler and Phase (Perfboard)

This is a bizarre little LFO that produces a wide range of pseudo random effects.

The Sawtooth Doubler and Sawtooth Phase are included on the module.

1 CGS Gate Sequencer with CV (Perfboard)

An 8-step sequencer designed for controlling pulsed or gated events, for rhythm and percussion.

The CV Adapter convers it to a traditional eight-step control voltage sequencer.

1 CGS Pulse/Clock Divider (Perfboard)

This module consists of several parts, a pulse divider with integer divisions between 2 and 8, and several logic elements. The divider is used to generate interrelated pulses for use in creating poly-rhythms, and unusual sequences. It can also be run at audio frequencies as a sub-oscillator/sub harmonic generator. The output pulse from each division is one clock cycle in length, and the relationship between pulses is fixed. Specifically, the /4 output will correspond to every second pulse from the /2 output. Likewise, the /8 will correspond to every second pulse from the /4 output, and the /6 will correspond to every second pulse from the /3 output. Needless to say, the /2 and /3 groups are not related to each other, or to the /5 or /7 outputs. All however share a common external reset, so they can be synchronized. All outputs go high on reset.

Some ideas on how to use this module:

Feed a clock signal into the input of the pulse divider. The divided signal is available simultaneously for each output. If running at audio frequencies, feed some of these to a mixer or other signal processing device. If running at low speed, try driving two different sequencers at the same time from different divisions.

Try feeding the /8 output into the reset - this will force all to synchronize to a /7 count, with the lesser divisions becoming "syncopated".

An AND gate could be used to control a clock signal. If the second input is LOW, no clock signal passes. If the second input is high, the signal passes unimpeded. Of course, there are a lot more things that can be done with the logic gates. For example, the /6 and /7 outputs could be ANDed together, and that would give a pulse every 6 x 7 (42) clock pulses (i.e. 1 pulse immediately the pulse divider is reset, and the second 42 pulses after that etc.).

1 CGS Burst Generator (Dual) (Perfboard)

This module is a rhythm and timing accessory. It generates a burst of gate or trigger pulses at various speeds as set from a front panel control.

At higher speeds it can be used for washboard, maracas or similar rapid-burst percussive effects when connected to the appropriate sound generating device such as a ringing oscillator.

At lower speeds it can be used to step a sequencer a certain number of steps or retrigger an envelope shaper. The output pulses are quite narrow when the specified component values are used, and would best be described as trigger pulses in synths that distinguish gates from triggers. Increasing some component values will give longer gate like pulses.

1 CGS Drum Simulator (Dual) (Perfboard)

This module is the embodiment of the classic twin-T circuit in a form that is suitable for connection to modular synthesizers. It contains 4 separate drum sounds, each individually triggered, as well as adjustable harmonic content.

1 Grant Richter CV Twister/Wave Warper (Perfboard)

This is a circuit adapted from the Sandin Image Processor. The original circuit was used to give "solarized" effects to video signals.

The basic idea is to use diodes to split the input voltage into three sections - plus, minus and "near zero". Each section is then run to a scalable follow/invert circuit. Since the breakpoints are fixed by the diode voltage drop, an input "span" control allows adjustment of the breakpoint relative to the input voltage range. The output "Gain" control then allows boosting the signal back up to the 10 volt range.

1 CGS Synthacon/Steiner VCF (Perfboard)

This module is a "tribute" module, based on the Steiner-Parker Synthacon VCF.

Unlike the original, this version allows signals to be fed into all inputs simultaneously. If the same signal is used in all inputs, the result is reminiscent of a phaser. The real fun starts when you feed different signals into each input, then you get a frequency based "interpolating scanner", where panning between different sound sources is possible, though also subject to the frequency at which they are running.

Each of the filter type inputs has its own level control. The ALL input is also affected by these level pots as it mixed with the individual inputs prior to the level controls.

If using only a single input, it may be better to feed the signal into the ALL input, and adjust the level pots to select LP, BP or HP, rather than changing the patch cord between the specific input jacks.

1 CGS Boolean Logic Gates (Perfboard)

Four boolean logic elements, two inverters an OR gate and an AND gate for the processing of gate and trigger signals.

1 Synth X Ensign Random Gate Generator - Uncertainty Module (Perfboard)

Dual 555 Timer based random Gate generators - Includes White Noise Generator Output

1 BugBrand Pattern Generator (Perfboard)

Dual 4 step pattern generator with CV outputs. Input two clocks to a side and complex patterns are formed based on the binary relationship of the clocks at any point in time. Produces a Trigger output at each change.

1 CGS Gated Comparitor (Perfboard)

This module takes a Clock source and a Signal source as inputs and creates 4 gate outputs in a pattern.

1 Blacet Frequency Divider (copy) (Perfboard)

The Frequency Divider converts a monophonic analog signal applied to the "IN" jack into digital pulses which are divided by two sections of CMOS digital counters. One section, controlled by the 4 pots mix divisions 1, 1.5, 2, and 3 together to form complex sub octave waveforms. The output signal is present at the lower "OUT" jack.

The second counter section, controlled by the rotary switch on the top of the module, divides the input signal by 6 thru 10. For example, a 440 Hz signal divided by 10 would result in a 44 Hz signal at the two "Pulse Out" jacks.

1 Polyfusion 2044 Copy - Envelope Follower/Gate Extractor (EFG) (Perfboard)

An envelope follower takes an audio input and converts it into a control voltage. This control voltage will rise and fall with the overall volume of the input signal. The louder the input, the bigger the output of envelope follower. The EFG has1 CV outputs available Switchable between Fast, Medium and Slow. The Fast is useful for tracking fast moving cymbal and hi-hat patterns. The slower one is more useful in processing single instruments. By using the CV output to control VCAs and VCFs it is very easy to create synchronised patterns that keep in perfect time with a drum machine or other musical input.

Another feature of the EFG, is the provision of a gate extractor. This part analyses the peaks in the music and creates a gate type signal in time with these peaks. This can be used to trigger envelope generators in time with an external drum loop or click track. A Gate Threshold rotory control enablesyou to get clean gate signals from all sorts of input material.

1 EFM VCO/VCA Combination module (Perfboard)

This OTA core VCO is based on the National Semiconductor application notes. It has one one-volt per octive input, sync and three control voltage inputs for modulation.

Featuring native triangle and square outputs. The sine output is derived from the tri using a system 100 style tri to sine converter.

There is a classic OTA VCA also on this board just because it's always nice to have lots of VCAs around.

1 Ian Fritz Design Dual AD/AR Envelope Generators (Perfboard)

1 Ray Wilson Design Triple Ramp/Sine/Sawtooth LFO's (Perfboard)

1 Triple Pulse/Octave Divider (Unknown Designer) (Perfboard)

Provides 1 and 2 octave down division of Audio or Pulse signals

1 4 Input Mono Mixer with VU Meters (Perfboard)

4 input mono mixer with 2 outputs.

1 Keyboard 1v/Octave CV Controller ( MFOS /Ray Wilson PCB)

1 Thomas Henry 'Mankato' VCF PCB

1 Fonik Attenuverting Mixer PCB

1 Thomas Henry VC QFG PCB (Voltage Controlled Quadrature Function Generator)

1 Ian Fritz Design Driven Double Well Chaos (Perfboard)

1 Passive Attenuator / CV Distributer (Perfboard)

1 Stereo Reverb

Repackaged Radio Shack

DIY Modular Synth Overview

DIY Electronic Instruments

Elektor Formant

Circuits & Links

Klee Sequencer

Quad Bass++

Sound Lab Ultimate Keyboard Synth

Lunetta

Home

Contact? Questions? Try This (A=leadingedgefm)
A@yahoo.com or PM me at Electro-music.com, nick = RF